- Model one role at a time (for example registered nurses). Enter each time block or shift, and say whether the unit is open or closed in that block.
- Enter concurrent patients, the maximum patients per direct-care worker for this role, any additional charge or supervisory worker required above that ratio, the workers scheduled, and those unavailable at the same time (breaks, leave, other assignments).
- The ratio must come from a verified local policy or be labeled a planning assumption. There is no default universal ratio. Record the source below.
- Optional: a minimum staffing floor for the block, and how many available workers hold the required qualification (reported as a separate skill-mix flag).
All computation runs in your browser; nothing is stored or transmitted.
When to Use
Use this planner when a dialysis manager needs to see which block of the roster fails the coverage rule the unit has chosen, by how many workers, and for how many worker-hours. It answers a scheduling question, not a safety question.
Two United States studies motivate attention to staffing. Among 236,126 adults starting in-center hemodialysis, facilities in the highest versus lowest quartile of annual patient-to-patient care technician ratio were associated with higher mortality (incidence rate ratio 1.07; 95% confidence interval 1.02–1.12) and lower transplantation (0.80; 0.71–0.91) (Plantinga et al., 2024). In hospitalized acute kidney injury, each additional patient per registered nurse was associated with higher odds of 30-day death (odds ratio 1.07; 1.01–1.13) (Iroegbu et al., 2026). Both are observational, and both use annual or hospital-level measures, not simultaneous bedside assignments, so neither supplies a safe shift ratio.
Philippine licensing reference
Department of Health (DOH) Administrative Order No. 2012-0001 (effective 2012) sets, for licensed hemodialysis clinics, a nurse-to-hemodialysis-station ratio of no more than 1:4, a physician-on-duty-to-station ratio of no more than 1:15, and at least one nurse per shift with current advanced cardiac life support (ACLS) training. The DOH licensing assessment tool (DOH-HDC-LTO-AT, rev. 03) applies the same 1:4 nurse-to-patient-station ratio, and the order was confirmed as the current dialysis licensing rule in November 2026. The button below loads the 1:4 nurse figure with its source. This tool still never reports compliance: a licensing minimum is a floor, and your licensing officer’s reading is final.
Pearls & Pitfalls
Peaks, not averages
Coverage fails at start-up and take-down, when patients are connected and disconnected at once. Split the day into blocks that capture those peaks rather than one average shift.
Unavailable is not optional
A worker on break, covering an isolation station, or helping in a code is not available for the ratio during that time. Enter them in U, or the roster will look covered when it is not.
Do not import study quartiles
Annual facility patient-to-staff ratios from cohort studies are a different metric from patients per worker at one moment. Do not type a study quartile into the ratio field.
Dialysis Shift Coverage Planner
Required workers Q = ceil(concurrent patients ÷ patients per worker) + additional charge workers, or the entered minimum if higher. Available workers B = scheduled − unavailable. Gap = max(0, Q − B).
| Block | Hours | Unit | Concurrent patients | Patients per worker | Extra charge | Scheduled | Unavailable | Minimum (opt.) | Qualified available (opt.) | Remove |
|---|
What This Does Not Estimate
Results describe coverage against the assumptions you entered. They are not “safe” or “unsafe,” and not a regulatory pass or fail. The planner does not estimate deaths, hospitalizations, or infections prevented by adding staff, and it does not check competencies, physical layout, infection-control demands, or backup availability.
Next steps: compare with actual peak census, staggered start and finish times, breaks, isolation needs, and the competencies of each scheduled person; review with your nurse manager and licensing guidance.
Formula & Methods
Final requirement = max(Q, Qmin) when a minimum is entered
B = K − U
Gap = max(0, Q − B); covered when B ≥ Q under the entered assumptions
Peak gap = largest block gap
Missing worker-hours = Σ (gap × block hours), only for nonoverlapping blocks
Validation: N, K, U, C, and minimum are whole numbers; R > 0 when patients are present; 0 ≤ U ≤ K. An open unit with no patients keeps the charge worker and any entered minimum. A block marked closed has no modeled requirement; the planner never infers closure from zero patients.
Illustrative example (hypothetical): 24 concurrent patients, R = 4, C = 1, K = 7, U = 1 gives Q = 7, B = 6, gap = 1; an 8-hour block has 8 missing worker-hours. With 25 patients, Q = ceil(25 ÷ 4) + 1 = 8.
Evidence
The patient care technician cohort (Plantinga et al., 2024) and the hospitalized acute kidney injury nursing study (Iroegbu et al., 2026) show associations between staffing and outcomes at the facility or hospital level, with residual confounding possible. Focus groups with US technicians describe ill-defined roles, nonstandard training, and high burnout risk (Urbanski et al., 2025). None of these studies validates a ratio or this tool; the Philippine figure loaded by the button is a licensing minimum, not an outcome-derived standard (Department of Health, 2012, 2015).
